Lux Products Thermostat T10 1141SA User Manual

INSTALLATION & OPERATION  
INSTALLATION AND  
OPERATING INSTRUCTIONS  
1). THERMOSTAT LOCATION  
For accurate temperature control and comfort, correct  
location is very important. On new installations, the  
guidelines listed below should be followed as closely as  
possible. When replacing an old thermostat, install the new  
one in the same location unless these conditions suggest  
otherwise.  
52014  
1. Locate the thermostat on an inside wall about five feet  
above the floor, where it is easy to install and adjust. It  
should be in a room that is used often, such as a  
family room.  
2. Do not install it where there are unusual heating  
conditions, such as direct sunlight, close to a lamp,  
radio, television, radiator, register, near a fireplace, or  
other heat producing appliance. Also, check for hot  
water pipes within the wall, or a stove on the other  
side of the wall.  
T10-1141SA  
3. Do not locate in unusual cooling conditions, such as on  
an outside wall, or one separating an unheated room, or  
in drafts from stairwells, doors, or windows.  
HEATING ONLY THERMOSTAT  
4. Do not locate in a damp or humid area. This can  
shorten thermostat life due to corrosion.  
5. Do not locate where air circulation is poor, such as in  
a corner, alcove, or behind an open door.  
6. Do not install until all construction work and painting  
have been completed.  
2) TOOLS REQUIRED  
Wirestripper or knife, drill with 316" bit, screwdriver, level  
and a pencil.  
3) REMOVING OLD THERMOSTAT  
Please read all instructions carefully. As you complete  
each step, check the adjoining square .  
Disconnect electricity and turn off gas to the heater.  
Remove cover from old thermostat.  
Loosen all screws.  
Disconnect wires from thermostat, making sure they do  
not fall back inside the wall.  
Strip insulation 38" from wire ends and clean off any  
corrosion.  
Fill wall opening with non-combustible insulation to  
prevent drafts from  
affecting thermostat.  
4) INSTALLING NEW THERMOSTAT  
Place new decorative wall plate (if supplied), Figure 3,  
over wall opening. Decorative wall plate can optionally  
be left off.  
Remove Front Cover of new thermostat by inserting a  
finger in the side of the thermostat and gently prying  
away each corner. Place Base, Figure 2, on wall plate  
over wall opening. Mark wall with pencil at mounting  
holes as shown in Figure 2. Now lay wall plate and  
base to the side.  
SPECIFICATIONS  
ELECTRICAL RATING.............24 Vac (30 Vac Maximum)  
SWITCH ACTION ............................Open Contact Switch  
ANTICIPATOR RATING................................0.15A to 1.2A  
TEMPERATURE RANGE...............................50°F to 90°F  
Drill two holes with 316" bit, 1" deep.  
Insert plastic screw anchors into drilled holes, flush  
with wall surface.  
Bring wires through large hole in decorative wall plate  
and through Hole For Wires in Base.  
Fasten Base loosely to wall using two mounting  
screws. Place a level against the bottom of the Base,  
adjust until it is level and then tighten mounting screws  
to secure the Base.  
© 2007 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED  
 

LaCie Computer Drive Little Big Disk User Manual
Lincoln Electric Welder SVM132 A User Manual
Makita Power Hammer HR2230 User Manual
Mamiya Digital Camera 211125 User Manual
Maytag Cooktop W10274255A User Manual
Maytag Freezer MAV 39 User Manual
Maytag Range W10419390A User Manual
Maytag Washer MFW9700SB1 User Manual
McCulloch Chainsaw 414 User Manual
Metabo Trimmer HS 8545 User Manual