Lux Products Thermostat T20 1141SA User Manual

INSTALLATION & OPERATION  
INSTALLATION AND OPERATING  
INSTRUCTIONS  
1). THERMOSTAT LOCATION  
For accurate temperature control and comfort, correct location is very  
important. On new installations, the guidelines listed below should be  
followed as closely as possible. When replacing an old thermostat,  
install the new one in the same location unless these conditions  
suggest otherwise.  
52021  
1. Locate the thermostat on an inside wall about five feet above the floor,  
where it is easy to install and adjust. It should be in a room that is used  
often, such as a family room.  
2. Do not install it where there are unusual heating conditions, such as  
direct sunlight, close to a lamp, radio, television, radiator, register, near  
a fireplace, or other heat producing appliance. Also, check for hot  
water pipes within the wall, or a stove on the other side of the wall.  
3. Do not locate in unusual cooling conditions, such as on an outside wall, or  
one separating an unheated room, or in drafts from stairwells, doors, or  
windows.  
4. Do not locate in a damp or humid area. This can shorten thermostat life  
due to corrosion.  
5. Do not locate where air circulation is poor, such as in a corner, alcove,  
or behind an open door.  
T20-1141SA  
HEATING ONLY THERMOSTAT  
6. Do not install until all construction work and painting have been  
completed.  
2) TOOLS REQUIRED  
Wirestripper or knife, drill with 316" bit, screwdriver, level and a pencil.  
3) REMOVING OLD THERMOSTAT  
Please read all instructions carefully. As you complete each step, check  
50 60 70 80 90  
10 15 20 25 30  
the adjoining square .  
Disconnect electricity and turn off gas to the heater.  
Remove cover from old thermostat.  
Loosen all screws.  
Disconnect wires from thermostat, making sure they do not fall back inside  
the wall.  
LUX  
20  
25  
1650  
80  
30  
70  
10  
50  
90  
Strip insulation 38" from wire ends and clean off any corrosion.  
Fill wall opening with non-combustible insulation to prevent drafts from  
affecting thermostat.  
4) INSTALLING NEW THERMOSTAT  
Place new decorative wall plate (if supplied), Figure 3, over wall  
opening. Decorative wall plate can optionally be left off.  
Remove Front Cover of new thermostat by inserting a finger in the side  
of the thermostat and gently prying away each corner. Place Base,  
Figure 2, on wall plate over wall opening. Mark wall with pencil at  
mounting holes as shown in Figure 2. Now lay wall plate and base to  
the side.  
Drill two holes with 316" bit, 1" deep.  
Insert plastic screw anchors into drilled holes, flush with wall surface.  
Bring wires through large hole in decorative wall plate and through  
Hole For Wires in Base.  
Fasten Base loosely to wall using two mounting screws. Place a level  
against the bottom of the Base, adjust until it is level and then tighten  
mounting screws to secure the Base.  
SPECIFICATIONS  
ELECTRICAL RATING  
24 Vac (30 Vac Maximum)  
SWITCH ACTION  
Open Contact Switch  
ANTICIPATOR RATING  
0.15A to 1.2A  
TEMPERATURE RANGE  
50°F to 90°F  
LUX PRODUCTS CORPORATION  
Mt. Laurel, New Jersey, 08054 USA  
© COPYRIGHT 2006 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED  
 

Kuppersbusch USA Cooktop GKS97510 M UL User Manual
Learning Resources Games LER 5054 User Manual
LG Electronics Clothes Dryer DLEY1201V User Manual
LG Electronics Universal Remote 202B User Manual
Life Fitness Fitness Equipment M051 00K59 0014 User Manual
Lincoln Electric Portable Generator IM10074 User Manual
Magnavox TV DVD Combo 20MF251W User Manual
Marantz CD Player CC3000 User Manual
Maytag Cooktop MGC4430BD User Manual
Maytag Range W10239459A User Manual