Ultra Start Automobile Alarm 45xx Series User Manual

Covers All 45xx Series 2way Remote Starter/ Alarms  
-The system must be placed into Service Mode before any service work is started on the vehicle. It is  
the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no  
liability or responsibility for accidental starting of the vehicle.  
- CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)  
- The Hood Pin Safety Switch Must Always be Installed!  
- Never Install Automatic Transmission Remote Starters into a Manual Transmission Vehicle!  
 
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE  
Page 3  
Remote Start - Automatic Transmission  
1. Press and release button #3.  
2. The park lights will flash and the siren will chirp one time.  
3. The vehicle will then remote start. The park lights will flash four  
2
3
1
times then remain on while the vehicle is running. The run timer  
on the LCD will begin to countdown.  
4
4. The vehicle will continue to run for the programmed runtime*.  
Never remote start if the vehicle is parked in a Garage.  
Operate in a well ventilated area only.  
Note: If the remote starter fails to start, the park lights will flash a  
Trouble Shooting Code. Count the number of flashes and  
refer to the Diagnostics Chart on page 15.  
Remote Stop  
2
3
1
1.Press and hold button #3 for three seconds. The remote starter  
will shut down. The park lights will flash and the siren will chirp  
two times to confirm shutdown.  
4
Note: Pressing the brake pedal or opening the hood will also shut  
down the remote starter.  
Extended Run Time  
1.Press and release button #3 while the vehicle is running.  
2.The system will respond with one park light flash and one siren  
chirp to confirm Extended Runtime.  
2
3
1
4
The system will reset the run time*.  
Note: Extended runtime will not work if the runtime is programmed  
for 4 Minutes.  
*Default 15 minutes  
 
OWNER’S GUIDE  
Page 4  
2way REMOTE STARTER/ ALARM  
Idle Mode  
1. While the vehicle is running with key, press button #3.  
2
3
1
4
2. The park lights will turn on and the siren will chirp once.  
3. Turn the ignition key off and the vehicle will continue to run.  
4. Exit the vehicle and leave it running safely without leaving the  
keys in the Ignition.  
Note: Always lock the doors while the vehicle is left running  
unattended. The vehicle will stay running for the  
programmed runtime (Default 15 minutes)  
Turbo Timer Mode  
2
3
1
4
1.While the vehicle is running with key, press button #4.  
2.The park lights will turn on and the siren will chirp once.  
3.Turn the ignition key off and the vehicle will continue to run for  
approximately 2 minutes.  
Note: Always lock the doors while the vehicle is left running  
unattended.  
Status Update  
2
3
1
4
This feature is used to check the status of the vehicle. If the  
system does not update the remote after completing a function  
press Button #4 on the transmitter. The remote will then display the  
current status of the system on the LCD screen.  
If the system is out of operating range the remote transmitter will  
beep three times quicky after a button is pressed. The antenna icon  
on the top of the LCD will be gone or show no bars next to the icon.  
 
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE  
Page 5  
Reservation Mode- Manual Transmission Only  
Manual transmission remote starters must be set into Reservation Mode before  
the remote starter will activate. There are two different ways to place the system  
into Reservation Mode. The activation type of Reservation Mode is determined  
when the system is installed. The default setting is Auto Reservation Mode.  
Auto Reservation Mode  
Step 1 - While the vehicle is running with the key, place the transmission into neutral  
and apply the park brake.  
Step 2 - Press and release the brake pedal twice. The park lights will flash twice,  
the siren will chirp twice and the doors will unlock (optional).  
Step 3 - Turn the ignition key off and the vehicle will continue running.  
Step 4 - Exit the vehicle and close all the doors. The vehicle will then shut off *.  
Manual Reservation Mode (Dealer Programmable Feature)  
Step 1 - While the vehicle is running with the key, place the transmission into neutral  
and apply the park brake.  
Step 2 - Press and release button #4. The park lights will flash twice, the siren  
will chirp twice and the doors will unlock (optional).  
Step 3 - Turn the ignition key off and the vehicle will continue running.  
Step 4 - Exit the vehicle and close all the doors.  
Step 5 - Press and hold button #3 for 3 seconds, the vehicle will then shut off.  
*****THE VEHICLE MAY NOW BE SAFELY REMOTE STARTED.*****  
(See pages 3&4 for Remote Starter Functions.)  
If Reservation Mode is not set, the remote starter will not activate. When  
button #4 is pressed the park lights will flash 4 times. 4 flashes is the diagnostic  
code for “Not in Reservation Mode”  
Note: Reservation Mode will reset if the doors of the vehicle are opened. To re-enter  
the vehicle without canceling the Reservation Mode (forgot something..) The  
vehicle must first be remote started. While the vehicle is running the door may  
be opened, when done in the vehicle, close the door and hold button #3  
until the remote starter shuts off.  
* If the vehicle has dome light delay, the vehicle may stay running until the dome  
light turns off. This is normally no longer than 30 seconds.  
 
OWNER’S GUIDE  
2way REMOTE STARTER/ ALARM  
Page 6  
Lock Doors and Arm Alarm  
1.Press and release button #1 on the remote transmitter.  
2.The park lights will flash and the siren will chirp one time.  
3.The doors will lock.  
2
3
1
4
4.The LEDs on the antenna will start flashing within five seconds.  
Note: If installed, the starter disable will activate.  
* To Lock/Arm without chirps, press #1 and #2 at the same time.  
Unlock Doors and Disarm Alarm  
2
3
1
4
1.Press and release button #2 on the remote transmitter.  
2.The park lights will flash and the siren will chirp two times.  
3.The doors will unlock.  
4.The LEDs on the antenna will stop flashing.  
Note: If installed, the starter disable will deactivate.  
* To Unlock/Disarm without chirps, press #1 and #2 at the same time.  
Priority Unlock Feature (Optional Feature)  
1. Press and release button #2 on the remote transmitter. The park  
lights will flash, the siren will chirp two times and the drivers door  
will unlock.  
2
3
1
4
2. Press and release button #2 again and the remain doors will unlock.  
Note: Button #2 must be pressed a second time within 3 seconds.  
Trunk Release  
1. Press and hold button #2 and the doors will unlock, continue holding  
button #2, the trunk release will activate. The trunk release will be  
confirmed by one park light flash and one siren chirp.  
2
3
1
4
Note: The trunk release output will not activate when the ignition key  
is in the “On” position.  
 
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE  
Page 7  
Car Finder Mode  
Car Finder is a feature that can be used to find your vehicle in a  
crowded parking lot.  
2
3
1
4
1. Press and release button #4 twice within 3 seconds.  
2. The park lights will flash and the siren will chirp five times to  
draw attention to the location of the vehicle.  
3. The remote will beep and display the systems current status.  
Panic Mode  
Activating Panic Mode  
1. Press and hold Button #1 for three seconds.  
2. The park light will begin to flash and the siren will activate.  
Panic mode will stay activated for one minute.  
2
3
1
4
Note: If installed the starter disable will activate.  
Disabling Panic Mode  
Press and release Button #1 or Button #2 to disable Panic Mode.  
Note: If installed the starter disable will deactivate.  
Silent Arm and Disarm  
Press and release buttons #1 and #2 at the same time.  
If the doors were locked this will unlock the doors without chirping  
the siren. The park lights will flash as confirmation of lock/ unlocking.  
2
3
1
4
Note: The siren can be programmed off by the remote transmitter.  
This will only delete Arm and Disarm chips, the alarm is still  
fully functional.  
 
OWNER’S GUIDE  
Page 8  
2way REMOTE STARTER/ ALARM  
Siren On/Off  
When this feature is programmed on the siren will only activate  
when the alarm is triggered or if the Car Finder is activated.  
1. Press and hold button #4 until the Timer Mode icon begins to  
flash.  
2
3
1
4
2. Press and release button #1 four times or until the siren icon  
begins to flash.  
3. To turn the siren Off press button #2. Press button #4 to exit.  
To turn the siren back on, press button #3 while the siren icon  
is flashing.  
Auxiliary Output 1 (Optional)  
Auxiliary Output are optional outputs from the system. These outputs  
Can be used to activate such things as power window roll-up/ down  
modules or to open and close a power sun roof.  
2
3
1
4
To Activate Auxiliary #1  
1. Press and hold buttons #1 and #3.  
2. The park lights will flash and the siren will chirp 1 time.  
3. The auxiliary output will stay activated until the button are released.  
Auxiliary Output 2 (Optional)  
Auxiliary Output are optional outputs from the system. These outputs  
Can be used to activate such things as power window roll-up/ down  
modules or to open and close a power sun roof.  
2
3
1
4
To Activate Auxiliary #2  
1. Press and hold buttons #2 and #3.  
2. The park lights will flash and the siren will chirp 1 time.  
3. The auxiliary output will stay activated until the button are released.  
 
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE  
Page 9  
Cold Start/Timer Mode  
Cold Start Mode will start the vehicle at a user selectable start interval or  
temperature setting. The vehicle can be set to start once every 1, 2, 3 or 4  
hours in Timer Mode or to start at 0,-5,-15 or -25 Celsius in Temperature  
Mode (LT Models Only) for a maximum 12 starts. The vehicle will start at  
the selected start interval/ temperature and run for the programmed runtime  
(Normally 15min). Cold Start Mode must be set each time the user wishes  
to use this feature.  
Example- Timer Mode. If the 4 hour start cycle was selected, the vehicle  
will start once every 4 hours and run for the programmed runtime then turn  
off. This setting will keep the vehicle in Cold Start Mode for up to 2 days  
before deactivating.  
2
3
1
4
Example- Temp Mode (LT models only). If the -15 Celsius start cycle  
was selected, the system will monitor the temperature until it falls below  
-15, at this time the remote starter will activate for the programmed runtime.  
The system will then wait 2 hours before checking the temperature again.  
To Enter Cold Start Mode.  
Press and release button #4, then press and hold Button #3 for 6 seconds  
or until park lights turn on. While the park lights are on the start cycle can  
be selected.  
Interval/ Temperature  
1 hour or 0 Celsius  
2 hour or -5 Celsius  
3 hour or -15 Celsius  
4 hour or -25 Celsius  
Press To Select  
Park Light Confirmation  
Press button #1 1 Park light flash  
Press button #2 2 Park light flashes  
Press button #3 3 Park light flashes  
Press button #4 4 Park light flashes  
Note: The optional Low Temp sensor must be installed for the Temperature  
Sensor settings to be available. (LT Models only)  
To Cancel Cold Start Mode  
Press and release button #4, then press and hold button #3 for six seconds.  
Stepping on the brake or turning on the ignition will cancel Cold Start.  
Cancellation of Cold Start Mode will be confirmed with two park light  
flashes and two siren chirps.  
 
OWNER’S GUIDE  
Page 10  
2way REMOTE STARTER/ ALARM  
LCD DISPLAY  
STATUS CHECK MODE This feature is used to  
check the status of the system. To check the status  
press and release Button #4 on the remote  
transmitter. The remote will display the icons of the  
active features on the LCD screen.  
STATUS ICONS These icons display the current status of the system. The  
icons may not all be present on the screen at all times, certain icons will only  
turn on when a feature is activated.  
ANTENNA ICON- This icon will be visible or show a series of lines  
next to the icon whenever the remote is within transmitting range of the  
vehicle. The icon will disappear when out of transmitting range.  
KEY ICON- This icon will begin to flash when the remote starter button is  
first pressed. After the vehicle has started this icon will stay on solid.  
SIREN ICON- This icon indicates that the alarm has been triggered. The  
remote will start to beep and the siren icon will come on solid at the same  
time as the icon for the violated zone.  
TRUNK ICON- This icon will be displayed on the LCD screen when the  
trunk release is activated by the remote transmitter. This icon will be  
displayed until the system is armed or if the status button is pressed.  
BATTERY ICON- This icon is always present when the LCD screen. This  
icon will indicate the current battery level for the remote transmitter. The  
black area of the icon will disappear as the battery level decreases.  
RUN TIMER- This icon activates during remote starting. The bar graph will  
count down in 2 minute increments, indicating how much time is left on the  
remote starter’s runtime.  
 
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE  
Page 11  
LCD DISPLAY  
User programmable features  
This Feature allows the user to program system features from the transmitter. The  
following icons will be displayed on the LCD to determine the status of the feature.  
To Enter User Program Mode  
1. Press and hold button #4 for three seconds. The Timer Icon will begin to flash,  
the system is now in User Program Mode.  
2. Press button #1 to scroll the list of features. Selected feature icon will begin to  
flash. Press button #2 to turn the feature icon Off, Press button #3 to turn the  
feature icon On. Press button #4 to exit program mode and save settings.  
*If the remote is not used for 20 seconds the system will exit Program Mode.  
TIMER ICON- When this icon is displayed in the left program column if  
confirms that the Timer Mode has been programmed ON. When this icon  
is turned on in remote program mode the Cold Start feature will be  
activated. Cold Start will default to the last time or temperature setting.  
KEY ICON- When this icon is displayed the remote starter has  
encountered a start fault. The start fault must be corrected before the  
remote starter will activate again.  
HORN ICON(Chirp Delete) - This icon indicates the status of the chirp  
delete feature. If the icon is on, the horn will work normally. If the icon is  
not displayed the chirp delete feature is on and the horn will not chirp.  
Note: Chirp delete disables the Lock and Unlock chirps Only.  
SHOCK SENSOR ICON - This icon indicates the status of the shock  
sensor. If the icon is present on the LCD screen the shock sensor is active.  
SERVICE MODE ICON- This icon indicates the status of the Service  
Mode feature. If this icon is present, the system is in Service Mode.  
*While in Service Mode, only the keyless entry features will operate.  
?
VIBRATION/SOUND ICON- This icon indicates the status of the  
Vibration and Sound features of the transmitter. If the icon is on, the  
remote will vibrate and not beep. (Not on all Models)  
To activate this feature press and hold buttons #3 and #4 four 5 seconds.  
 
OWNER’S GUIDE  
Page 12  
2way REMOTE STARTER/ ALARM  
Shock Sensor Programming/ Adjustment  
Press and hold buttons #1 and #2 for three seconds. The park lights will flash  
and the siren will three times.  
While the park lights are on strike the vehicle with the amount of force wanted to  
trigger the alarm*. Hit the vehicle with the same amount of force three time, the  
siren will chirp each time the system detects the Impact.  
2
3
1
4
*Strike the vehicle with the palm of the hand, be careful not to impact the vehicle in  
a area that may cause damage. The most common location for testing and setting  
the shock sensor is the A-pillar. The A-Pillar is the metal support that runs from the  
roof of the vehicle to the hood area.  
Temporary Shock Sensor Bypass  
2
3
1
4
This feature can be used if the vehicle is parked in an area with above average  
noise or vibrations. (Airports, construction zone...)  
1st  
2nd  
To Temporally Bypass The Shock  
Press the button #1 to arm the alarm then press button #3 within three seconds.  
The system will chirp once when the lock button is pressed and once when the start  
button is pressed. The shock sensor will be disabled until the system is disarmed  
and the rearmed again.  
Note: The shock sensor can be programmed by the remote transmitter. Hold  
button #4 until the 1st program icon begins to flash the use button #1 to scroll to the  
hammer symbol. Press button #2 to deactivate the shock sensor. To turn the sensor  
back on select the hammer symbol and press the button #3.  
 
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE  
Page 13  
Setting The Time (On equipped models only)  
1) Press and hold buttons #1 and #4 until the minute portion of the  
2
3
1
4
clock begins to flash.  
2) To set the minute, press button #3 to increase and button #2 to  
decrease the minute.  
3) To set the hour, press button #1 and the hour portion of the clock  
will begin to flash.  
4) To set the hour, press button #3 to increase and button #2 to  
decrease the hour. To set the AM/ PM icon, continue changing the  
hour until the appropriate icon is displayed.  
Note: The remote will exit clock adjust if there is no activity for 20  
seconds.  
Silent Remote Operation (On equipped models only)  
This feature allows the user to switch the remote sound or vibrations  
features on or off.  
The default setting on the system is audible sound confirmation (Beeps)  
from the remote transmitter when a button is pressed on the remote  
transmitter. To turn the “Beeps” off and have vibration confirmation,  
press and hold buttons #3 and #4 on the remote transmitter for 5 seconds.  
The vibration icon (See on left) will appear and the remote will vibrate  
once as confirmation. To set the remote back to “Beeps” press and hold  
buttons #3 and #4 for 5 seconds. The vibration icon will turn off and the  
remote will beep as confirmation.  
 
OWNER’S GUIDE  
Page 14  
2way REMOTE STARTER/ ALARM  
Service Mode  
ATTENTION: TO AVOID SERIOUS INJURY, this remote start system must be  
set into Service Mode before any under hood servicing is started. Service  
Mode will prevent the vehicle from starting while the vehicle is being  
serviced. It is the sole responsibility of the vehicle’s owner to place the  
system into Service Mode. The manufacture accepts no responsibility for  
accidental starting of the vehicle while the vehicle is being serviced.  
System Service Mode(Valet) - By Remote  
ACTIVATE/DEACTIVATE Service Mode (User Programmable Feature)  
1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)  
2 - Press button #1 Five times or until the ? starts flashing on the screen.  
3 - Press button #3 to activate or #2 to deactivate Service Mode.  
4 - Press button #4 to exit User Program Mode.  
The System is Now in Service Mode.  
5 - The siren will chirp once and the LEDs on the antenna will come on solid.  
Emergency Service Mode - (Valet Mode)  
This feature will disable the system except for lock, unlock and trunk functions.  
This mode is used if a remote is misplaced, damaged or if the system malfunctions.  
If the system was installed with a starter disable this feature will disable the starter  
disable relay and allow the vehicle to start.  
Activate/ Deactivate Service Mode (Valet Mode)  
To enter Service Mode turn the ignition key to the “On” position then press and hold  
the Program Button located on the antenna for 5 seconds. The system will chirp the  
siren 5 times as confirmation. To Deactivate Service Mode, turn the ignition key  
“On” and hold the Program Button Until The siren Chirps 2 times.  
While the system is in Service Mode the remote starter and alarm functions will be  
disabled and the LEDs on the antenna will come “On” steady. As confirmation of  
Service Mode. The door lock, unlock and the trunk release will still be operational.  
 
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE  
Page 15  
Diagnostics/ Diagnostics Chart  
If the remote starter does not activate when button #3 is pressed the park lights  
will flash a diagnostic to indicate what shutdown input has been triggered.  
Example when the start button is pressed the park lights flash 3 times slowly.  
Looking at the chart below this would indicate that the system is in Service Mode.  
Park Lights  
3 Flashes  
3 Slow Flashes Solid  
4 Slow Flashes Series of 4 Flashes  
5 Flashes  
Status LEDs  
Series of 3 Flashes  
Diagnostic Code  
Door Opened “M” Models  
System is in Service Mode  
Not in Reservation Mode “M” units  
Hood Pin Opened  
Series of 5 Flashes  
5 Slow Flashes Series of 5 Flashes  
Ignition On During Start Attempt  
Brake Pedal Shutdown  
Tach Lock-Out  
6 Flashes  
7 Flashes  
Series of 6 Flashes  
Series of 7 Flashes  
Diagnostic Memory  
LED Flashes  
5 Flashes  
6 Flashes  
7 Flashes  
8 Flashes  
Diagnostic  
The system was shutdown by the hood pin input  
The system was shutdown by the brake switch input  
The system did not detect the tach signal  
The system made 3 start attempts without starting  
Being that the installer does not always see when the system shuts down or fails to  
start, Diagnostic Memory will store in memory up to four shutdown codes.  
This information can then be accessed to determine the source of the shutdown.  
To Enter Diagnostic Mode:  
Step 1 - Turn the ignition on then off. Press the Program Button and release.  
Step 2 - The system will respond with three park light flashes and the siren will chirp  
the same number of times as the events in memory. (Maximum 4 events, 4 chirps).  
NOTE: If the siren does not chirp, there are no events in memory.  
Step 3 - Press the Program Button once to view the last shut down code. The siren  
will chirp once to confirm code one. (If the siren does not chirp, there are no codes.)  
Step 4 - The LEDs on the antenna will flash a code corresponding to a shut down  
trigger. Press the Program Button again to check the second code. The siren will chirp  
twice to confirm code two.  
Step 5 - To Clear Diagnostic Memory. While in Diagnostic Mode press and hold the  
Program Button for five seconds. The park lights will flash and the siren will chirp once.  
NOTE: Once diagnostic memory has 4 shutdown events in memory, the system will not  
Record any further shutdown events until the system memory has been cleared.  
 
OWNER’S GUIDE  
Page 16  
2way REMOTE STARTER/ ALARM  
Limited Lifetime Warranty  
The manufacturer warrants to the original purchaser of their remote starters and alarms, that the product  
shall be free from defects in material and workmanship. However, should this product be proven to be  
defective, within a two year period from the original date of purchase, the manufacturer will, without  
charge to the purchaser (excluding any charges incurred to have the product delivered to the  
manufacturer), repair or replace any part of the remote starter and/or alarm which the manufacturer agrees  
to be defective. After the initial 2 year period the manufacture shall repair or replace defective products with  
a nominal processing fee of $30.00 USD. All warranties apply to the original purchaser and the vehicle in  
which it was originally installed ONLY. Repairs or replacement of defective modules shall remain at the  
discretion of the manufacturer. All other parts, components, accessories and/or optional equipment  
pertaining to the remote starter and alarm are not included in the manufacturer’s warranty.  
This warranty is non-transferable. Request for warranty service from any Factory Authorized Dealer  
must be accompanied with the original purchase receipt or have product registered by authorized  
dealer on manufacturer’s website.  
Failure to comply with any of these conditions may result in warranty being voided.  
This warranty does not cover the following: removal and reinstall labor charges, shipping charges, abuse,  
misuse, or accidental damages to the remote starter and alarm, automobile, and/or parts there of. This  
warranty is void upon modification, repairs, or alterations of any part of the product. The manufacturer does  
not guarantee or insure against theft of the vehicle or its contents. Alarm models are designed only to act  
as a deterrent against possible theft. This alarm may qualify for auto insurance discounts, contact your  
Insurance Agent for further information . The manufacturer shall not be held liable for any consequential  
damages due to breach of this or any other warranty, expressed, or implied. This warranty gives you  
specific legal rights. Your specific legal rights may vary for each region.  
CERTAIN DAMAGES EXCLUDED - The manufacturer expressly disclaims any liability or responsibility  
for incidental damages caused by the product, including economic loss, loss of use of the product, car  
rentals, or any other costs relating to the care and custody of the product. The manufacturer disclaims  
liability or responsibility for any consequential damages caused by the product or resulting from its use,  
including the cost of repairing or replacing other property damaged by the product or caused by its use,  
whether or not the product is working properly. The product is intended to deter unauthorized use of the  
vehicles in which it is installed. The manufacturer does not warrant that the product is fool-safe against  
theft and/or vandalism and/or human error or misuse. The manufacturer accepts no liability or  
responsibility for any damage of any kind whatsoever caused to any vehicle in which the product is  
installed or any resulting damage from its use. The manufacturer accepts no responsibility or liability for  
any damage resulting to or theft of the vehicle or its contents, caused or alleged to be caused, directly or  
indirectly, by failure of the product.  
MANUAL TRANSMISSION STARTERS the installation of a remote starter MUST only be done with a  
specified manual transmission starter. It is the sole responsibility of the vehicles operator to  
insure that the vehicle is left with the transmission in neutral position when the remote starter is in  
use. The manual transmission starter is designed to be an added measure of safety ONLY! The  
manufacturer does not guarantee or insure against any damages or loss of life that could result in  
the event of a remote starter starting while the vehicle is in gear. Manual transmission models are  
designed only to act as a deterrent against the vehicle starting in gear, this is the vehicle’s owner’s  
and operator’s responsibility.  
 

Technicolor Thomson Stereo System MS4200 User Manual
Toshiba Label Maker B 852 TS12 QP User Manual
Toshiba MP3 Player SD V394 User Manual
TRENDnet Printer TEW P1PG User Manual
Triarch Indoor Furnishings 29320 1 User Manual
True Manufacturing Company Freezer GDIM 26 User Manual
Vector Automobile Accessories VEC012POB User Manual
ViewSonic Computer Monitor E70fb User Manual
Weber Gas Grill 56203 User Manual
Weber Gas Grill S 460TM User Manual